Polarization Extinction Ratio
a measure of the degree of polarization. AKA: PER
See Also: Fiber Optic Cable Test
-
product
10 A True DC Micro-Ohmmeter
AUTO-OHM 10
The Vanguard Auto-Ohm 10 is a 10-ampere battery powered micro-ohmmeter designed for low-resistance-measuring applications such as the measurement of resistance in circuit breaker contacts, bushing contact joints, and welding joints. The unit is powered by four 3400mAh, 3.7Vdc Li-Ion rechargeable batteries. With these high capacity batteries, up to 2,900 tests per charge (10A/2 second duration) can be performed in the field. The Auto-Ohm 10 features a built-in charger that can charge the batteries when the unit is not in use.
-
product
Clamp-on Transducer
CA1000D
Measure current without disconnecting circuit under test. Measure to 1000A DC or AC. Outputs 1mV per Amp, operates on 2V range of any DMM.
-
product
Extensometers for Simple Performance Testing of Asphalt
Model 3909
Jinan Testing Equipment IE Corporation
Designed for measuring axial displacements in the simple performance tests prescribed by NCHRP Report 465, and determining dynamic modulus of hot mix asphalt per AASHTO TP062.
-
product
Universal Preamplifier 14
UP14
For Two Dimensional Magnetic Recording (TDMR) and Heat-assisted Magnetic Recording (HAMR) Headamplifiers. Universal Preamplifier 14 (UP14) is designed for TDMR and HAMR Head Amplifiers. With new Guzik RWA4000 TDMR, UP14 allows to process signals from three Read Channels. It also supports two high speed data channels for Write data and Laser data. UP14 has two channels for dynamic TFC control and allows to program TFC power per sector and close loop TFC power control in each channel. UP14 can gen...show more -
product
Liquid Chromatograph Mass Spectrometer
LCMS-8040
The LCMS-8040 was designed to provide significantly higher sensitivity while maintaining the high speed offered by the LCMS-8030. Ultrafast MRM transition speeds, up to 555 MRMs per second (dwell times of 1 msec and pause times of 1 msec) are achieved. In addition, the LCMS-8040 features the polarity switching at 15 msec and high speed scanning rate of 15,000 u/sec. By incorporating newly improved ion optics UF-Lens™ and UFsweeper™ II collision cell technology, the LCMS-8040 provides higher multiple reaction monitoring (MRM) sensitivity. This higher sensitivity expands the potential range of LC/MS/MS applications.
-
product
16 Bit PXIe Gen-3 Digitizer With 2 Channels 1 GS/s And 4GS Memory
RazorMax / CSX 161G2
The new extremely fast and high-resolution Gage digitizers of the series RazorMax Express CompuScope offer with a 3U Single slot PXI Express card a resolution of 16 bit and a sampling rate of 1 GS/s (per channel).
-
product
Data Loggers
The unit can acquire data from on-board interfaces at rates of up to 10 kilosamples per second, and from remote units via communications links. A high-performance on-board PowerPC microprocessor offering over 1000MIPS processing power hosts customer applications for real-time data analysis. Application code may be autocoded using our Graphical Development Environment (GDE) from Matlab/Simulink control modules. Data is logged to 2GB of on-board Flash memory and downloaded for analysis via a Gigabit Ethernet network connection.
-
product
PXI 2.5W Programmable Resistor Module, 1-Channel, 2.5Ω to 773kΩ
40-251-143
The 40-251-143 is a programmable resistor module with 1 channel which can be set between 2.5Ω and 773kΩ with 1Ω resolution The 40-251 range provides a simple solution for applications requiring up to 2.5W of power handling per channel. The 40-251 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
product
MCB Thermal Trip Calibration Test Bench (IEC 60898 Cl 9.10.1.2, Annex I.1, IS)
The test system is designed and customized to carry out 2.55*Intest as per Table 7 (test c) of IEC 60898 (also mentioned for routine testing of MCBs. The test is done at dc current to exactly analyze and correct the bimetallic properties of the MCB as far as thermal tripping is concerned. The unit comes with a pneumatically operated test fixture with in-built dc stepper motor that is controlled by a micro controller / PC to calibrate the breaker into a narrow tripping band programmed by the user.
-
product
Compact Temperature Chamber
FB1.5V-UHC Series
Based on the proven Bemco FB1.5V Compact Temperature Chamber, the FB1.5V-UHC offers spectacular temperature change rates in excess of 75 C per minute. With an extremely compact footprint these chambers cost about 1/3 of the amount of a typical 2-zone thermal shock chamber such as a Bemco FS2V.
-
product
Charge-Discharge, Li-ion Cell Formation, and Test Solution
BT2200
The BT2200 charge-discharge platform is cost-effective and easily configurable for Li-Ion cell formation and lifetime cell cycling. A modular design supports cells requiring maximum currents ranging from ± 6 A to ± 800 A, with up to 256 cells or channels per chassis. You can quickly deploy different channel configurations as your cell requirements change and capacities grow.
-
product
Data Lake Analytics
Easily develop and run massively parallel data transformation and processing programs in U-SQL, R, Python, and .NET over petabytes of data. With no infrastructure to manage, you can process data on demand, scale instantly, and only pay per job.
-
product
Cable Continuity Tester, RS232, DB9 In Line Signal, Network, 21.01 mm, 35 mm, 45.01 mm
72-9265
The 72-9265 is an In-Line Signal Link Tester. Quickly test DB9 connections with this handy tester. No need to carry bulky, expensive cable testers to test only one or two cable types. Mini link tester fits easily in your pocket or tool box and requires no external power. Connects in-line and displays signal data connectivity on LED's per each conductor. Save time and money by diagnosing connectivity issues.
-
product
PXI 5W Programmable Resistor Module, 1-Channel, 2Ω to 52.4kΩ
40-252-133
The 40-252-133 is a programmable resistor module with 1 channel which can be set between 2Ω and 52.4kΩ with 1Ω resolution The 40-252 range provides a simple solution for applications requiring up to 5W of power handling per channel. The 40-252 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
product
8-Channel ADC Module
FMC168 – LPC
Sundance Multiprocessor Technology Ltd.
The FMC168 is a digitizer FMC featuring eight ADC channels with 16-bit resolution and 250 Mega samples per second sampling rate per channel. With a flexible clock generation and distribution scheme, the FMC168 allows control on sampling frequency and analog input gain through serial communication with a carrier card. The FMC168 design is based on the TI ADS42LB69 Dual Channel 16-Bit 250 MSPS A/D, is equipped with power supply and temperature monitoring, and offers several power-down modes to switch off unused functions.
-
product
Tunable Laser Source, High Power And Lowest SSE, Top Line
N7776C
The new Keysight N7776C top line tunable laser source is designed to reach best-in-class accuracy in static and swept operation for outstanding test efficiency. Two-way sweeps up to 200 nm/s speed with sub-picometer repeatability and without impacting the specified dynamic accuracy accelerate wavelength-dependent alignment processes and the automated calibration of wavelength-selective devices. Shorter time to testing and faster swept-wavelength tests help reduce test cost per device, improve test margins and lower the cost of ownership.
-
product
Dynamic Weighing System for Wheel Loaders
Loadtronic 3
Modern wheel loaders are designed for increased productivity under all conditions. It is important not to lose these properties after installing a weighing system. The Loadtronic 3 weighing system will never tell you to slow down, even on rough surfaces. It helps your company save time and money and increases your profit. This is possible because the Loadtronic 3 has the built-in dynamics system. Drive as you normally do, move fast and flexible. Load more tons per hour. Instead of giving away valuable goods, load the correct amount every time.
-
product
AMIDA 3001XP Tester
AMIDA has introduced two new analog/mixed-signal and logic options in the AMIDA-3000 series in recent years—the AMIDA-3001XP and AMIDA-3KS test systems. Both reinforce the AMIDA-3000 series' ability to provide cost-optimized test solutions for a variety of consumer components in power management and mobile device components. The AMIDA-3000 series provides more than twice the number of analog channels of its modules per test system, thus greatly reducing the acquisition cost of each channel and m...show more -
product
4 Discrete/Switch I/O Channels (±100 V, 3 A/Ch.)
DT3
The DT3 module (the enhanced version) feature 4 independent, high current, isolated, programmable channels that can be used for input voltage measurements (±100 V), or as a bi-directional current switch (up to 3 A per channel). When programmed as a switch with the switch closed, both the current through the switch and the voltage across the switch can be monitored. These modules include diode clamping on each channel. Clamping is useful for inductive loads, such as relays and short circuit protection.
-
product
General Purpose Radiation Survey Meter/Geiger Counter
Rad 100™
The RAD 100™ is a general purpose radiation survey meter/geiger counter that detects and measures alpha, beta, gamma, and X-radiation. It is intended for personal safety and educational purposes. Like the popular Radalert® 100X, the RAD 100™ features a 3-second update on its digital liquid crystal display (LCD). The LCD shows the current radiation level in your choice of microSieverts per hour (SI units) or mR/hr for gamma radiation measurements. For mixed sources (alpha, beta, gamma) the CPM m...show more -
product
Data Loggers
Premier Electrosystems has a wide range of data loggers to suit your needs. All our data loggers can be customized as per requirement. Data loggers are electronic devices which automatically monitor and record environmental parameters over time, allowing conditions to be measured, documented, analysed and validated. The data logger contains a sensor to receive the information and a computer chip to store it. Then the information stored in the data logger is transferred to a computer for analysis.
-
product
Short Hot Stick
HS-120R
Standard Electric Works Co., Ltd
● Single foamed hot stick.● Universal sunrise fitting on the head to fit special tool fittings.● Rated at 100 kV per 300mm (5 minutes).● Can be connected to 275 HP HV proximity detector, 21X HVD capacitive HV detector and 277 HP Non-contact HV detector.● Meets IEC 60855.● Reasonable price.● Accessories
-
product
6000 Series Analog I/O Modules
Series 6000 analog I/O modules condition, amplify, filter and digitize signals from virtually any transducer. All modules have conditioning & amplifier per channel and nearly all modules allow for setting bridge completion, shunt calibration, transducer power, gain, etc. individually per channel. Following the conditioning/amplifier stage, multi-pole Bessel or Butterworth analog filters are provided on each channel and can be set or bypassed individually by program control. A number of the m...show more -
product
16 Bit PXIe Gen-3 Digitizer With 4 Channels 1 GS/s And 4GS Memory
RazorMax / CSX 161G4
The new extremely fast and high-resolution Gage digitizers of the series RazorMax Express CompuScope offer with a 3U Single slot PXI Express card a resolution of 16 bit and a sampling rate of 1 GS/s (per channel).
-
product
PXI 2.5W Programmable Resistor Module, 2-Channel, 3Ω to 5.82MΩ
40-251-052
The 40-251-052 is a programmable resistor module with 2 channels which can be set between 3Ω and 5.82MΩ with 0.5Ω resolution The 40-251 range provides a simple solution for applications requiring up to 2.5W of power handling per channel. The 40-251 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
product
Wind Speed Sensor/Anemometer
ENVIROMUX-WSS
Rugged anemometer. 3-cup rotor pressed on a stainless steel shaft. Reed switch and magnet providing one pulse per rotation. Rotor diameter: 5 inches. Speed range: ~ 3 mph to 125+ mph (~5 kph to over 200 kph). Rugged Delrin body with bronze and Rulon bushings. Flat aluminum mounting bracket with 2 holes. esigned to be mounted on top of a pole or bracket. 100 feet of exterior grade wire. Maximum cable length: 1000 ft (305m).
-
product
Reach-In Solar Panel Test Chamber
For testing various size solar panels WIEBER designs and manufactures Solar Panel Test Chamber. The test are to be performed according to various standards of ASTM, IEC, UC etc. Solar panels need to pass environmental tests as per IEC and other standards requirements to prove their long term performance and resistance to temperature and humidity extremes. Solor Chamber also known as Solar Photovoltaic Testing Chamber and PV Module Test Chamber.
-
product
D-Mic Auto Test System
BK9013
If your company produces millions of D-mics per month, take a look at the BK9013. Based on our BK3012V2 D-Mic Tester, the fully automatic BK9013 is our fastest D-Mic test system. With 4 or 8 couplers, the BK9013 can simultaneously test and sort up to 8 D-Mics into 8 passing grades and 7 different causes of failure in just a few seconds! You can view the results in real time or store them to analyze later.
-
product
Mission Critical, Fault Tolerant Power Supplies
Series HSF
- Hot-swappable plug-in power supplies.- Designed to be combined in an N+1 fault-tolerant power system.- Front panel voltage adjustment trimmer for adjustment of output voltage.- Built-in forced current sharing and or-ing diodes.- May also be used independently as a multi-output power supply.- Designed to be sustainable - new models are backward compatible with existing racks.- Available in 1U and 3U sizes. Mounts in 19-, 23-, and 24-inch equipment racks.- All models include power factor correct...show more -
product
Conductivity Meters
There are both standard and a waterproof conductivity meter, as well as a conductivity meter available for flowing water or pure water (highly recommended for specific industries) as well as the ones with different conductivity measurement ranges. An important factor is that a conductivity meter normally measures electric conductivity in µS/cm, however it can also take measurements in mg/l (for direct reading of content in dissolved solid substances). The relation is established as follows: 2 µS/cm = 1ppm (parts per million) = 1 mg/l. Compensated temperature in the conductivity meter can be automatic or by hand.
